{"product_id":"civic-integra-obd1-engine-harness-1992-1995","title":"Civic Integra OBD1 Engine Harness 1992-1995 – Fit for Honda Civic Integra B16 B18 D16, D\u0026B-Series, CNCH-0BD1-1, FIC30","description":"\u003ch2\u003eCivic Integra OBD1 Engine Harness 1992-1995 – B16, B18, D16, D and B-Series\u003c\/h2\u003e\n\u003cp\u003eThis Civic Integra OBD1 engine harness is a replacement engine wiring loom listed for 1992-1995 Honda Civic and Integra models with B16, B18 and D16 engines. It is sold under the part numbers CNCH-0BD1-1 and FIC30 and is built with OBD1 (92-95) computer connectors. Easy Life Markets sells it for owners whose original loom has gone brittle with age, and for builders putting a B-series or D-series engine into an OBD1 chassis.\u003c\/p\u003e\n\n\u003cp\u003eThirty years of heat does a lot of damage to an engine loom. Insulation cracks, connector tabs snap and old repairs pile up, and the result is a car with intermittent faults that are almost impossible to pin down. A new \u003ca href=\"https:\/\/en.wikipedia.org\/wiki\/Cable_harness\" target=\"_blank\" rel=\"noopener\"\u003ecable harness\u003c\/a\u003e replaces all of that in one go. The supplier describes this one as about 95% plug and play, with PET coated wires that have a maximum thermal rating of 150 °C.\u003c\/p\u003e\n\n\u003ch2\u003eWhat Is Included\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e1 x engine harness with the sensor and actuator connectors listed below\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe supplier is specific about what is not included:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe charge harness. It must be run independently.\u003c\/li\u003e\n\u003cli\u003eHeadlight wiring and dash light wiring.\u003c\/li\u003e\n\u003cli\u003eECU\/PCM plugs.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eConnectors on the Harness\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eInjectors 1–4\u003c\/li\u003e\n\u003cli\u003eMAP sensor\u003c\/li\u003e\n\u003cli\u003eTPS sensor\u003c\/li\u003e\n\u003cli\u003eIdle control motor\u003c\/li\u003e\n\u003cli\u003eIntake air temperature\u003c\/li\u003e\n\u003cli\u003eEngine coolant temperature\u003c\/li\u003e\n\u003cli\u003eWater temperature sending unit (for the gauge cluster)\u003c\/li\u003e\n\u003cli\u003eOxygen sensor (primary, 4 wire)\u003c\/li\u003e\n\u003cli\u003eKnock sensor\u003c\/li\u003e\n\u003cli\u003eVTEC solenoid\u003c\/li\u003e\n\u003cli\u003eOil pressure sending unit\u003c\/li\u003e\n\u003cli\u003eElectronic speed sensor\u003c\/li\u003e\n\u003cli\u003eAlternator\u003c\/li\u003e\n\u003cli\u003eStarter signal\u003c\/li\u003e\n\u003cli\u003eFan switch\u003c\/li\u003e\n\u003cli\u003eReverse lights\u003c\/li\u003e\n\u003cli\u003eGround\u003c\/li\u003e\n\u003cli\u003ePower distribution cap\u003c\/li\u003e\n\u003cli\u003e2 extra wires\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct type:\u003c\/strong\u003e Engine wiring harness\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart numbers:\u003c\/strong\u003e CNCH-0BD1-1, FIC30\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eListed application:\u003c\/strong\u003e Honda Civic and Integra, B16, B18 and D16, 1992–1995\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector standard:\u003c\/strong\u003e OBD1 (92-95) computer connectors\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWire covering:\u003c\/strong\u003e PET coated, maximum thermal rating 150 °C\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInjector type required:\u003c\/strong\u003e High impedance. Not compatible with a resistor box\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFit, per the supplier:\u003c\/strong\u003e About 95% plug and play\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Unbranded aftermarket\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOption:\u003c\/strong\u003e 08688674 (one version)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSKU:\u003c\/strong\u003e CJQT290808701AZ\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eChecking Fitment Before You Order\u003c\/h2\u003e\n\u003cp\u003eThe supplier lists this harness for the Honda Civic and Integra with B16, B18 and D16 engines, 1992 to 1995, and adds that its compatibility charts are for reference only. Take that seriously. These cars have been swapped, converted and modified for decades, and what matters is what is in your engine bay today:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eConfirm your ECU is OBD1.\u003c\/strong\u003e This harness is made for the OBD1 computer used from 1992 to 1995. An OBD0 or OBD2 ECU needs a different loom or a conversion.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCheck your injectors.\u003c\/strong\u003e The harness must be used with high impedance injectors. If your setup uses low impedance injectors with a resistor box, this harness is not compatible.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGo through the connector list.\u003c\/strong\u003e Compare each connector above with the sensors on your engine. A non-VTEC engine, for example, will leave the VTEC solenoid plug unused.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePlan the charging circuit.\u003c\/strong\u003e The charge harness is not part of this loom, so you will need to keep or make your own.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompare part numbers.\u003c\/strong\u003e If you are replacing a harness sold as CNCH-0BD1-1 or FIC30, this is the listed match.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eThe supplier offers to check fitment against a part number. If you would like that done, \u003ca href=\"\/pages\/contact\"\u003esend us your details\u003c\/a\u003e along with your engine code and ECU type.\u003c\/p\u003e\n\n\u003ch2\u003eWhat \"95% Plug and Play\" Means in Practice\u003c\/h2\u003e\n\u003cp\u003eIt means most connectors should meet their sensors without cutting, but not all of them. Expect to deal with the charge wiring yourself, to find homes for the two extra wires if you need them, and possibly to adjust a lead or two depending on which engine and intake manifold you are running. Budget time for that rather than expecting a ten-minute swap.\u003c\/p\u003e\n\n\u003ch2\u003eSigns an Engine Harness Is Due for Replacement\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eFaults that appear and disappear when you move the loom\u003c\/li\u003e\n\u003cli\u003eSensor codes that return after the sensor itself has been replaced\u003c\/li\u003e\n\u003cli\u003eCracked, hard or sticky insulation, especially near the exhaust manifold\u003c\/li\u003e\n\u003cli\u003eBroken connector tabs held together with tape or cable ties\u003c\/li\u003e\n\u003cli\u003eEarlier repairs made with crimp connectors and mismatched wire\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eInstallation Tips\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eDisconnect the battery before you unplug anything.\u003c\/li\u003e\n\u003cli\u003eLabel every connector on the old harness as you remove it, and take photos of the routing.\u003c\/li\u003e\n\u003cli\u003eLay the new harness over the engine and connect the injectors first, then work outward to the sensors.\u003c\/li\u003e\n\u003cli\u003eKeep the loom away from the exhaust manifold and any moving parts, and use the original clips and brackets where you can.\u003c\/li\u003e\n\u003cli\u003eClean every ground point to bare metal. Poor grounds cause more running problems on these engines than failed sensors.\u003c\/li\u003e\n\u003cli\u003eBefore the first start, check for continuity on the main grounds and confirm the injector and ignition feeds have power.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eAn engine harness affects fuelling and ignition. If you are not confident with automotive wiring, have it fitted by a workshop that knows these Hondas.\u003c\/p\u003e\n\n\u003ch2\u003eWho This Harness Is For\u003c\/h2\u003e\n\u003cp\u003eOwners of 1992-1995 Civic and Integra models with tired original wiring, builders doing B-series or D-series swaps on an OBD1 ECU, and workshops that would rather fit a fresh loom than repair an old one wire by wire.\u003c\/p\u003e\n\n\u003ch2\u003eCommon Questions\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eIs this a genuine Honda harness?\u003c\/strong\u003e No. It is an unbranded aftermarket harness sold under the numbers CNCH-0BD1-1 and FIC30.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it include the ECU plugs?\u003c\/strong\u003e The supplier states that ECU\/PCM plugs, headlight wiring and dash light wiring are not included.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it with a resistor box?\u003c\/strong\u003e No. The supplier says it must be run with high impedance injectors and is not compatible with a resistor box.\u003c\/p\u003e\n\n\u003ch2\u003eBuy the Civic Integra OBD1 Engine Harness at Easy Life Markets\u003c\/h2\u003e\n\u003cp\u003eOrder the Civic Integra OBD1 engine harness on this page. The current price and availability are shown on this page. Please read our \u003ca href=\"\/pages\/return-refund-policy\"\u003ereturn and refund policy\u003c\/a\u003e before buying.\u003c\/p\u003e\n\n\u003ch2\u003eRelated Products\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/products\/78410-s04-901-speed-sensor\"\u003e78410-S04-901 speed sensor for Honda Civic\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/products\/aluminum-spark-plug-cover-engine-harness\"\u003eAluminum spark plug cover\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/products\/cr-v-iridium-spark-plug-odyssey-acura\"\u003eCR-V iridium spark plug\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eSee more in the \u003ca href=\"\/collections\/wiring-harnesses\"\u003ewiring harnesses\u003c\/a\u003e, \u003ca href=\"\/collections\/electrical\"\u003eelectrical\u003c\/a\u003e and \u003ca href=\"\/collections\/auto-parts\"\u003eauto parts\u003c\/a\u003e collections.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eNotice:\u003c\/strong\u003e California Prop 65 Warning.\u003c\/p\u003e\n\n\u003ch2\u003eProduct Photos\u003c\/h2\u003e\n\u003cp\u003e\n\u003cimg src=\"https:\/\/cf.cjdropshipping.com\/b2ecf6d9-fd66-4634-bee8-94641abfc4ac.jpg\" alt=\"Civic Integra OBD1 engine harness connectors, close view\" style=\"max-width:100%;\"\u003e\n\u003cimg src=\"https:\/\/cf.cjdropshipping.com\/047ca5ba-4b37-4426-bfeb-dd32baf2ed37.jpg\" alt=\"Complete engine harness laid out\" style=\"max-width:100%;\"\u003e\n\u003cimg src=\"https:\/\/cf.cjdropshipping.com\/dcdb5364-a2bd-44d5-8471-32178058962d.jpg\" alt=\"Engine harness, additional view\" style=\"max-width:100%;\"\u003e\n\u003cimg src=\"https:\/\/cf.cjdropshipping.com\/7e129973-d987-4696-a236-80637a6e2ebd.jpg\" alt=\"Engine harness, additional view\" style=\"max-width:100%;\"\u003e\n\u003cimg src=\"https:\/\/cf.cjdropshipping.com\/7659f2b3-fb56-4bf5-900e-e7c37e3e432d.jpg\" alt=\"Engine harness, additional view\" style=\"max-width:100%;\"\u003e\n\u003cimg src=\"https:\/\/cf.cjdropshipping.com\/09dee687-c859-4b7b-ad75-7937187491e0.jpg\" alt=\"Engine harness, additional view\" style=\"max-width:100%;\"\u003e\n\u003cimg src=\"https:\/\/cf.cjdropshipping.com\/8a53467c-d12b-438b-8eec-1c8ab9604a39.jpg\" alt=\"Engine harness multi-pin connectors\" style=\"max-width:100%;\"\u003e\n\u003c\/p\u003e","brand":"easylife markets","offers":[{"title":"08688674","offer_id":46973795008673,"sku":"CJQT290808701AZ","price":392.28,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0751\/2086\/9537\/files\/5ddad3c8-29a5-4cad-be5f-86ef52dafa9e.jpg?v=1788633913","url":"https:\/\/easylifemarketplace.com\/products\/civic-integra-obd1-engine-harness-1992-1995","provider":"Easy Life Markets","version":"1.0","type":"link"}