BMW Camshaft Position Sensor | 13627525014 13627546660

BMW camshaft position sensor, mounting flange

BMW Camshaft Position Sensor CPS for 128i 320i 323i 325i 328i 330i 528i 550i – Replaces 13627525014

Dhs. 120.55

BMW Camshaft Position Sensor – Replaces 13627525014, 13627546660, 13627558518, 13627594040

This BMW camshaft position sensor (CPS) is an aftermarket replacement for BMW part numbers 13627525014, 13627546660, 13627558518 and 13627594040. It is listed for a wide range of BMW models, including the 128i, 320i, 323i, 325i, 328i, 330i, 528i and 550i, and the supplier's attribute list also names the X5 and Z4. Easy Life Markets sells it as a single, unbranded replacement sensor for drivers and workshops dealing with camshaft sensor faults.

These BMW sensors are commonly used on six-cylinder petrol engines such as the N52 and N54, as well as some V8 engines, and many of those engines use two of them, one for the intake camshaft and one for the exhaust. This listing is for one sensor.

What the Sensor Does

The camshaft position sensor reads a trigger wheel on the camshaft and sends that signal to the engine control unit. On BMW engines with VANOS variable valve timing, the computer also uses it to check that the camshafts are where they should be. A failing sensor can upset starting, idle and the valve timing system.

Common Signs of a Bad Camshaft Sensor

Check engine light with camshaft position sensor or VANOS-related fault codes
Long cranking before the engine starts
Rough idle or stalling
Reduced power, sometimes with the engine going into a limp mode
Poor fuel economy

Oil in the sensor connector is a common problem on these engines. If you find oil in the plug, clean it and check the sensor seal as well as the sensor itself.

Compatibility

The listing title names these BMW models: 128i, 320i, 323i, 325i, 328i, 330i, 528i and 550i. The supplier's attribute list gives these examples with years:

BMW 328i, 2007–2014
BMW X5, 2007–2014
BMW Z4, 2006–2014

BMW fitted this sensor family to many models, but not to every engine in each range. The reliable check is the part number: if your old sensor or your BMW parts catalogue shows one of the numbers above, this is the matching replacement.

Part Numbers

OE reference numbers: 13627525014, 13627546660, 13627558518, 13627594040 (also written 13 62 7 525 014, etc.)
Other interchange numbers: 5S7403, PC770
Manufacturer part number: A0032A0062

Specifications

Product type: Camshaft position sensor
Brand: Unbranded (aftermarket replacement)
Condition: New
Number of sensors: 1
Placement: Engine compartment, cylinder head
Connector and wiring: As shown in the photos
SKU: CJQC271018701AZ

Installation Tips

Disconnect the battery and let the engine cool.
Unplug the connector and remove the single mounting bolt.
Twist and pull the old sensor out of the head.
Lightly oil the new sensor's O-ring with clean engine oil and push it into place.
Refit the bolt, reconnect the plug and clear the fault codes.

On most of these engines the sensors sit at the front of the cylinder head, but access varies by model.

Intake and Exhaust Sensors

Many BMW engines that use this sensor have two of them: one reading the intake camshaft and one reading the exhaust camshaft. The part numbers listed here have been used for both positions on many engines, but you should always confirm by checking the number on the sensor you are replacing. The fault code will usually tell you which sensor the engine computer is unhappy with. If both are original and the car has high mileage, replacing them as a pair is common, and you would order two of this item.

Diagnosing Before You Replace

Before fitting a new sensor, check the connector for oil, corrosion or damaged pins, and look at the wiring harness for chafing. Oil in the connector usually means oil has travelled up the sensor body, so clean the plug thoroughly when fitting the new sensor. It is also worth checking the oil level and condition, since low or old oil can cause VANOS-related faults that look similar to a sensor problem.

Who This Sensor Is For

This sensor suits BMW owners who handle their own maintenance, independent workshops that service BMWs regularly, and anyone replacing a failed camshaft sensor with a matching part number.

Common Questions

Is this a genuine BMW sensor? No. It is an unbranded aftermarket replacement that cross-references the BMW part numbers listed above.

Is it sold singly or as a pair? This listing is for one sensor. Order two if you want to replace both intake and exhaust sensors.

Do I need special tools? Usually just a socket or Torx bit for the mounting bolt, depending on the engine. Access varies by model.

Buy a BMW Camshaft Position Sensor at Easy Life Markets

You can order this BMW camshaft position sensor right here. The current price and availability are shown on this page. If you need help matching the part number, contact us, and please read our return and refund policy before buying.